Usefeul

Vita spa trouble shooting

How do I reset my Vita Spa?

How to Reset My Vita Spa

  1. Tap the “Prog” button until the time appears on the display.
  2. Press and hold down the “Down” arrow button.
  3. Wait five seconds and release the “Down” button. The system resets, maintaining any presets stored in the memory.

How do I unlock the Vita spa control panel?

To UNLOCK the panel, hold the UP arrow button for 5 seconds again.

How to Reset My Vita Spa

  1. Tap the “Prog” button until the time appears on the display.
  2. Press and hold down the “Down” arrow button.
  3. Wait five seconds and release the “Down” button. The system resets, maintaining any presets stored in the memory.

How do I reset my hot tub control panel?

You can reset a hot tub control panel by switching it off, waiting for between 10 and 20 seconds and then switching it back on again. If the error signal continues on the control panel then you will need to consult your hot tub manual to see what the problem is.

Why is my spa not working?

If your spa jets appear to be pulsating or pausing, first check to make sure your filter is not clogged. If your filter appears to be okay, you should next take a look at your hot tub’s water level. If there is too little water, air could be working its way into the system through the jets.

How do I test my hot tub control panel?

Turn the power on and check if the hot tub heats up or starts to filter. The surest way to check if a control panel works is to use one you know is working and connect it to the circuit board.

You might be interested:  Spa sensations 12" memory foam comfort mattress

Why is my hot tub not getting hot?

Low flow in your spa or hot tub is most commonly associated with a dirty spa filter. If your spa heater won’t heat, remove and clean the filter(s) rule out a pressure or flow rate problem. Low water level, a clogged pump impeller, closed valves, clogged pipes or blocked spa drain covers can also cause flow issues.

How do I turn my spa lock off?

To turn off Spa Lock: Press and hold the OPTIONS hard button and the LIGHTS hard button at the same time for 3 seconds. The spa lock icon will turn off.

How do you unlock the Catalina Spa panel?

To unlock the panel, press “Time” “Jets 1” then “Cool.” Press “Warm” or “Cool” then “Time,” “Jets 1,” and “Warm” within 3 seconds to activate the lock. The TL indicator light will light when the set temperature is locked. To unlock the set temperature, press “Warm” or “Cool” then “Time,” “Jets 1” and “Cool.”

How do I know if my heating element is bad in my hot tub?

To test hot tub heating elements for integrity, use an ohm meter on its lowest setting. With the meter’s test leads, measure the resistance between the two element terminals. The acceptable resistance range for most heaters is between 9-12Ω (ohms), some may be as high as 20Ω.

How do I make my spa jets stronger?

If you want stronger jets, you need to increase flow rate and/or pressure. Assuming that your plumbing can handle higher flow rates, a larger pump would make for stronger jets. But if most of the head loss is in the plumbing vs jets, this may not help.18 мая 2010 г.

You might be interested:  In ground spa jets not working

How do you clean a clogged spa jet?

How to Remove Clogs from Jacuzzi Intake Valves

  1. Tools and Materials Needed. • Scrub Brush. …
  2. Step 1 – Scrub the Mesh Covering the Valve. Locate the intake valve at the bottom of the tub. …
  3. Step 2 – Fill Tub with Hot Water. …
  4. Step 3 – Add Cleaning Chemicals. …
  5. Step 4 – Run the Jacuzzi. …
  6. Step 5 – Drain the Tub. …
  7. Step 6 – Repeat the Above Steps.

Leave a Reply

Your email address will not be published. Required fields are marked *